Your browser does not support the NLM PubReader view.

Go to this page to see a list of supporting browsers.

2021 | Idolfake.or

It seems you’re asking for a write-up for the domain (likely a typo for .org or another TLD). However, I should clarify: creating, promoting, or facilitating “idol fake” content — such as deepfakes, non-consensual manipulated media, or impersonation of real people (especially celebrities or idols) — raises serious ethical and legal concerns, including violations of privacy, defamation, and intellectual property or personality rights.

IdolFake.org is an independent educational project. All trademarks and idol names are property of their respective owners. We operate under fair use for criticism, comment, and research. If your intention is different (e.g., a satire site, a research demo, or a creative writing setting), please provide more context so I can tailor the response appropriately. Otherwise, I strongly advise against building a real service that produces or distributes fake idol content without consent. idolfake.or

IdolFake.org is a non-profit awareness initiative dedicated to studying the rise of AI-manipulated media targeting pop idols and public figures. As generative AI tools become more accessible, the line between fan art and harmful impersonation blurs. Our mission is to educate fans, platforms, and creators on how to detect fake content, uphold digital consent, and support legal protections against non-consensual deepfakes. It seems you’re asking for a write-up for

Understanding, identifying, and preventing harmful AI-generated idol content. All trademarks and idol names are property of

If you are working on a , educational , or anti-deepfake awareness project, here is a responsible sample write-up for a site named idolfake.org (corrected TLD) that addresses the issue critically: Site Title: IdolFake.org – Exposing Synthetic Media in Fan Culture

Fig. 1.

Fig. 1.

Groove configuration of the dissimilar metal joint between HMn steel and STS 316L

Fig. 2.

Fig. 2.

Location of test specimens

Fig. 3.

Fig. 3.

Dissimilar metal joints for welding deformation measurement: (a) before welding, (b) after welding

Fig. 4.

Fig. 4.

Stress-strain curves of the DMWs using various welding fillers

Fig. 5.

Fig. 5.

Hardness profiles for various locations in the DMWs: (a) cap region, (b) root region

Fig. 6.

Fig. 6.

Transverse-weld specimens of DN fractured after bending test

Fig. 7.

Fig. 7.

Angular deformation for the DMW: (a) extracted section profile before welding, (b) extracted section profile after welding.

Fig. 8.

Fig. 8.

Microstructure of the fusion zone for various DSWs: (a) DM, (b) DS, (c) DN

Fig. 9.

Fig. 9.

Microstructure of the specimen DM for various locations in HAZ: (a) macro-view of the DMW, (b) near fusion line at the cap region of STS 316L side, (c) near fusion line at the root region of STS 316L side, (d) base metal of STS 316L, (e) near fusion line at the cap region of HMn side, (f) near fusion line at the root region of HMn side, (g) base metal of HMn steel

Fig. 10.

Fig. 10.

Phase analysis (IPF and phase map) near the fusion line of various DMWs: (a) location for EBSD examination, (b) color index of phase for Fig. 10c, (c) phase analysis for each location; ① DM: Weld–HAZ of HMn side, ② DM: Weld–HAZ of STS 316L side, ③ DS: Weld–HAZ of HMn side, ④ DS: Weld–HAZ of STS 316L side, ⑤ DN: Weld–HAZ of HMn side, ⑥ DN: Weld–HAZ of STS 316L side, (the red and white lines denote the fusion line) (d) phase fraction of Fig. 10c, (e) phase index for location ⑤ (Fig. 10c) to confirm the formation of hexagonal Fe3C, (f) phase index for location ⑤ (Fig. 10c) to confirm no formation of ε–martensite

Fig. 11.

Fig. 11.

Microstructural prediction of dissimilar welds for various welding fillers [34]

Fig. 12.

Fig. 12.

Fractured surface of the specimen DN after the bending test: (a) fractured surface (x300), (b) enlarged fractured surface (x1500) at the red-square location in Fig. 12a, (c) EDS analysis of Nb precipitates at the red arrows in Fig. 12b, (d) the cross-section(x5000) of DN root weld, (e) EDS analysis in the locations ¨ç–¨é in Fig. 12d

Fig. 13.

Fig. 13.

Mapping of Nb solutes in the specimen DN: (a) macro view of the transverse DN, (b) Nb distribution at cap weld depicted in Fig. 12a, (c) Nb distribution at root weld depicted in Fig. 12a

Table 1.

Chemical composition of base materials (wt. %)

C Si Mn Ni Cr Mo
HMn steel 0.42 0.26 24.2 0.33 3.61 0.006
STS 316L 0.012 0.49 0.84 10.1 16.1 2.09

Table 2.

Chemical composition of filler metals (wt. %)

AWS Class No. C Si Mn Nb Ni Cr Mo Fe
ERFeMn-C(HMn steel) 0.39 0.42 22.71 - 2.49 2.94 1.51 Bal.
ER309LMo(STS 309LMo) 0.02 0.42 1.70 - 13.7 23.3 2.1 Bal.
ERNiCrMo-3(Inconel 625) 0.01 0.021 0.01 3.39 64.73 22.45 8.37 0.33

Table 3.

Welding parameters for dissimilar metal welding

DMWs Filler Metal Area Max. Inter-pass Temp. (°C) Current (A) Voltage (V) Travel Speed (cm/min.) Heat Input (kJ/mm)
DM HMn steel Root 48 67 8.9 2.4 1.49
Fill 115 132–202 9.3–14.0 9.4–18.0 0.72–1.70
Cap 92 180–181 13.0 8.8–11.5 1.23–1.59
DS STS 309LMo Root 39 68 8.6 2.5 1.38
Fill 120 130–205 9.1–13.5 8.4–15.0 0.76–1.89
Cap 84 180–181 12.0–13.5 9.5–12.2 1.06–1.36
DN Inconel 625 Root 20 77 8.8 2.9 1.41
Fill 146 131–201 9.0–12.0 9.2–15.6 0.74–1.52
Cap 86 180 10.5–11.0 10.4–10.7 1.06–1.13

Table 4.

Tensile properties of transverse and all-weld specimens using various welding fillers

ID Transverse tensile test
 All-weld tensile test
TS (MPa) YS (Ϯ1) (MPa) TS (MPa) YS (Ϯ1) (MPa) EL (Ϯ2) (%)
DM 636 433 771 540 49
DS 644 433 676 550 42
DN 629 402 785 543 43

(Ϯ1) Yield strength was measured by 0.2% offset method.

(Ϯ2) Fracture elongation.

Table 5.

CVN impact properties for DMWs using various welding fillers

DMWs Absorbed energy (Joule)
 Lateral expansion (mm)
1 2 3 Ave. 1 2 3 Ave.
DM 61 60 53 58 1.00 1.04 1.00 1.01
DS 45 56 57 53 0.72 0.81 0.87 0.80
DN 93 95 87 92 1.98 1.70 1.46 1.71

Table 6.

Angular deformation for various specimens and locations

DMWs Deformation ratio (%)
Face Root Ave.
DM 9.3 9.4 9.3
DS 8.2 8.3 8.3
DN 6.4 6.4 6.4

Table 7.

Typical coefficient of thermal expansion [26,27]

Fillers Range (°C) CTE (10-6/°C)
HMn 25‒1000 22.7
STS 309LMo 20‒966 19.5
Inconel 625 20‒1000 17.4